En50618 PV Cable Solar Cable Solar Power Cable

 Type TUV  solar cable

Standard
 Conductor:   1.5mm2-240mm2 tinned copper
   Insulation:   XLPO, low smoke, halogen-free,flame retardant, 
                        oil,abrasionchemical cross-linked compound                                                                          
      Sheath:   XLPO, low smoke, halogen-free,flame retardant, 
                       oil,abrasion,chemical cross-linked compound
     Voltage:   AC 600/1000 V – 720/1200 V & DC 900/1800 V
   Standard:    EN50618

Application:

For the cabling between the solar modules and as extension cable between the module strings and the DC/AC inverter Gable and flat roof photovoltaic systems Photovoltaic plants and solar parks Flexible or building-integrated PV systems including connecting photovoltaic power supply systems & can be used indoor & outdoor for flexible and fixed installations with high mechanical strength in extreme weather conditions. from – 40 deg.C to 120 deg.C maximum and Ozone & UV Resistant and full protection against Ultra Violet rays.
Product Features
Weather/UV-resistant acc. to HD 605/A1
Ozone-resistant according to EN 50396
Halogen-free and flame-retardant
Good notch and abrasion resistance
XLS-R = X-Linked Standard – Reduced Proven electron beam cross-linked quality
Cold Flexibility
Long Life about > 25 years
Suitable to common connector type
Electrical Properties
Nominal voltage U0/U acc. VDE AC 600/1000 V – 720/1200 V & DC 900/1800 V
Max. permitted DC voltage 1.8 kV (Conductor/Conductor. non earthed system
Working voltage : According to. TÜV 2 PfG 1169 DC 1000 V
Test voltage AC 6,5 kV for 5 min & DC 15 KV.
Voltage resistance tests according to EN 50395
Insulation Resistance – 1000 m-OHM / km minimum
Mechanical Properties
Minimum Bending Radius: 4 to 5 x Outer Diameter
Dynamic Penetration: According to requirement of Cables for PV systems 2 Pfg 1169/08.2007 Annex F
Notch Propagation: According to 2 Pfg 1169/08.2007 Annex G
Tensile Strength: 15 N/mm2 for insulation and 12.5 N/mm2 for
 sheathing – according to EN60811
Elongation of Insulation and sheathing: 125% – according to EN60811
Shore Hardness 85 According to DIN EN 53505
Shrinkage: 2% at 120°C according to EN 60811-1-3
EU Directives
The cables are RoHS (Restriction of certain Hazardous Substances) compliant as per EU Directives 2002/95/EC
Thermal Properties
Ambient temperature: -40 °C to 90°C (25 year life)
Conductor temperature: 120 °C max.
Short Circuit temperature: 200 °C for 5 sec.
Thermal Endurance Test: According to EN 60216-2
High Temperature Pressure: Test according to EN 60811-3-1
Damp – Heat Test: According to EN 60068-2-78
1000 hrs. at 90°C with 85% humidity

Chemical Characteristics
Mineral Oil Resistance: according to EN 60811-2-1 & vde 0473-811-2-1
Ozone Resistance: according to EN 50396 part 8.1.3 Method B
Weathering-UV Resistance: according to HD 605/A1 or DIN 53367
Ammonia resistant : 30 days in saturated ammonia atmosphere (internal testing)
Very good resistance to oil and chemicals
High wear and robust, abrasion resistant
Acid & Alkaline Resistance: According to EN 60811-2-1 (Oxal acid and sodium hydroxide)

Type UL solar cable

Standards:
UL-4703, UL-854, UL-44
UL 1685-FT4/IEEE 1202 (70,000 Btu/hr) Flame Test (1/0 AWG and larger)
ICEA T-29-520 (210,000 Btu/hr) Flame Test
NEMA WC70/ICEA S-95-658
NFPA 70: National Electrical Code (NEC)

Conductors:

aluminium compact stranded 
or Stranded conductors, uncoated copper per ASTM-B787 and ASTM-B8

Insulation:
Cross-linked polyethylene (XLPE) insulation per UL-854, UL-4703 and UL-44

voltage:

600v,1000v,2000v

Features:

Sunlight, ozone, and UV resistant

Moisture resistant

RoHS compliant

REACH compliant

-40°C to +150°C temperature range

Applications:
Type Photovoltaic copper conductors are suitable for outdoor rooftop applications without conduit and for use in conduits and raceways installed underground in conduit in wet locations, and where condensation and moisture accumulations within the conduit do not exceed 90ºC. Applications requiring direct burial is permitted for Type Photovoltaic per UL-854. Applications requiring type Photovoltaic conductor, temperatures shall not exceed 90ºC in wet or dry locations.

 
Features:
Available in 600V and 1000V/2000V. All cables comply with UL’s VW-1 (Vertical Wire) Flame Test. Insulation compounds are rated for flame and sunlight-resistance in all sizes and colors. Photovoltaic conductors of 1/0 through 1000 KCMIL are rated for CT use. Sequential foot markings located every foot on master reels only for 1 AWG through 1000 KCMIL unless otherwise specified. RoHS compliant. Flexibility at Low Temperature Test. Carries -40 °C  rating.

Details Show

Packing and shipping 

Company information

HeBei huatong wires&cables Group Co.,ltd.

which founded in1993,covers 15,000 square meters.With 400 sets of manufacturing machines and 200 pieces of equipment available for testing and inspecting,the company’s annual mannufacturi-ng capacity has reached 450 minllionUS dollars.

The enterprise has adapted international a-dvanced mannagement standards by fully implementing the accreditation of ISO9001Quality con-trol system, ISO1004 Envrionment management system,and OHSAS18001 Occupational health and safety management system.

Huatong’s products which consist of 15 series of cables and tens of thousands of specifications are widely used in different  key  national projects and industries .Our products are well liked by domestic and international customers that they have been exported to various countries and areas including the US,Netherlands, Italy,Russia,UK,Australia,Ethiopia,Ghaha,congo,Middle East ,and Southeast Asia.

\
FQ

(1).When can I get the price?

We usually quote within 6 hours after we get your inquiry. If you are very urgent to get the price, please call us or tell us in your e-mail so that we will regard your inquiry priority.

(2).How can I get a sample to check your quality?

After price confirmation, you can require for samples to check our quality. Sample is free, but the freight charge should be paid.

(3).How long can I expect to get the sample?

After you pay the freight charge and send us confirmed files, the samples will be ready for delivery in 3-7 days. The samples will be sent to you via express and arrive in 3~5 days. You can use your own express account orprepay us if you do not have an account.

(4).What about the lead time for mass production?

Honestly, it depends on the order quantity and the season you place the order.The best record we keep is delivering 10 kilometers cable within a week.