Suspension and La Crossarm 2500
Suspension and La Crossarm 2500 image
Get Latest Price Request a quote
Quick Details
Product Details
Any standard equivalent to GB/T 707 1988, 80×43, 5/8 and 100×48, 5.3/8.5 is accepted.
For suspension, T-off, angle and dead end assembly shall have a cross section dimension of
80 x 43 x 5/8mm
For transformer base U-cross arms shall have a dimension of 100x48x5.3/8.5
U-cross arms manufactured for suspension, T-off, angle, dead end and transformer base
assembly as per the drawing
To protect U-cross arms against corrosion U-cross arms shall be hot dip-galvanized
Yield strength of U-cross arm 240N/mm2
Test for yield stress
Percentage elongation test
Bend test
Chemical composition test
Galvanization tests thickness of Zn coating
Weight of Zn Coating
Uniformity of Zn coating
Adhesion test of Zn coating
Visual inspection
Weight verification
Dead end hook 382
Hook threaded nominal diameter (A) 16mm
Minor threaded diameter (W) 14
Thickness of nut (M), washer diameter and thickness as per BS standard
Yield strength of pin must be 240N/mm2
LV Hook from corrosion it shall be hot dip-galvanized
Visual inspection
Size inspection
Galvanizing test
Strength test
Suspension hook M16-380
Hook threaded nominal diameter (A) 16mm
Minor threaded diameter (W) 14
Thickness of nut (M), washer diameter and thickness as per BS standard
Yield strength of pin must be 240N/mm2
To protect LV Hook from corrosion it shall be hot dip-galvanized
Testing
Visual inspection
Size inspection
Galvanizing test
Strength test
The following testing shall be carried out
Dead End Clamp ,Anchoring Clamp
The clamps should be designed to Anchor LV AB cable with insulated messenger. The clamp
should anchor/hold the neutral messenger without damaging the insulation.
The clamp should conform to the standard NFC 33041 and 33042 or equivalent. The clamp
body should be made of corrosion resistant Aluminium alloy, bail should be of stainless steel
and self adjusting wedges should be weather and UV resistant polymer.
Anchoring assemblies are used to firmly attach the messenger of ABC to a support and
transmit the mechanical tension at the end of a run or to the supporting structures at a major
change in direction.
The suspension clamp shall be manufactured from weather and UV light resistant reinforced
nylon and aluminum alloy. The clamp should provide an additional insulation between the
cable and the pole.
Clamps should be fixed with pole by eyehook/bracket. Breaking load should not be less than
15kN
Suspension Assembly is used for supporting an ABC by installation on the messenger at an
intermediate point of support such as a pole. It can accommodate small angles of deviation up
to 30o. The clamp should hold insulated messenger of diameter range from 6mm up to 12 mm.
Visual examination
Dimensional and material verification
Tensile strength
Dielectric voltage test
Climatic & corrosion ageing
Endurance test under mechanical and thermal stresses
Electrical ageing
TYPE:APG-C4
NAME:Parallel groove clamp APG-C4
Specification
Material |
||
Material standard |
||
Range of conductor cross-section |
16…50/2.5…35 |
|
Range of conductor diameter, Al/Cu |
mm2 |
|
Tensile strength |
KN | 5 |
Thickness of zinc coating, |
mm |
43 |
Test voltage at 50Hz for one minute in water |
kV |
6 |
Al 35-300mm² Size 105*65mm Tri-bolts Bolt M10*60 Weight 560g
We are China Suspension and La Crossarm 2500 manufacture and supplier,You can get more details with Email,you will get cheap price or factory price.
Get Latest Price Request a quote
Popular Anchoring Clamp Products
PAM-06 ABC Aluminum Anchoring Clamp with Cross-Section 16-20 mm²
Tension Clamps (PA-1000/PA-1500/PA-2200)
Smico Products Electric Cable Accessories Wedge Dead End Anchor Clamp
High Quality Anchoring Dead End Clamp
Popular Crossarm Products
Alley Arm Brace Steel Crossarm HDG
Factory Price Alley Arm Brace for Pole Line Hardware
Galvanized Bracket Aerial for Corner
Crossarm 1800*65*65*6 Hot -DIP Galvanized Cross Overhead Line Fitting
Hot DIP Galvanized Double Span Angle Brace for Construction
Cheap Price Galvanized Steel Crossarm for Pole Line Fitting
Popular Dead End Hook Products
Pole Line Hardware Hot-DIP Galvanized Guy Dead End Hook
Pole Line Hardware Dead End Hook
M16, 300mm Long Bolt Nut and Washer
Earthing Rod 50X5X3 with Clamp
Popular jgtrade1 Products
Fjh-K Type Voltage Divder Rings
Bimetallic Terminal of Compression for Driver N º 2 AWG (2 holes)
6-35kv High Voltage Porcelain Wall Bushing
Tags: Anchoring Clamp, Crossarm, Dead End Hook, jgtrade1