Ttd Series 1kv 77-679A 1.5-400mm² Special Waterproof and Flame-Retardant Insulation Piercing Connector for Street Lamp Distribution System
Ttd Series 1kv 77-679A 1.5-400mm² Special Waterproof and Flame-Retardant Insulation Piercing Connector for Street Lamp Distribution System image
Get Latest Price Request a quote
Basic Info.
Packaging & Delivery
Product Description
Product Description
The insulation puncture clamp (connector) is mainly composed of an insulation shell, a puncture blade, a waterproof rubber pad, and a torque bolt. When making a cable branch connection, insert the branch cable into the branch cap and determine the branch position of the main line, then use a socket wrench to tighten the torque nut on the clamp. With the tightening of the torque nut, the upper and lower parts of the clamp have hidden insulators with piercing blades At the same time, the arc-shaped sealing rubber pad wrapped around the piercing blade is gradually clinging to the cable insulation layer, and the piercing blade also begins to pierce the cable insulation layer and metal conductor. When the sealing degree of the sealing rubber pad and insulating grease and the contact between the puncture blade and the metal body reach the best effect, the torque nut will automatically fall off, at this time, the installation is completed and the contact point sealing and electrical effect reach the best.
Insulation piercing clamps can be divided into 1KV, 10KV, and 20KV insulation piercing clamps according to voltage classification.
According to the functional classification, it can be divided into ordinary insulation piercing wire clips, electrical inspection grounding insulation piercing wire clips, lightning protection and arc proof insulation piercing wire clips, and fireproof insulation piercing wire clips
Technical paramete
Product features and advantage
Structural features:
1. Puncture structure, simple installation, no need to peel the insulated wire;
2. Torque nut, constant puncture pressure, ensure good electrical connection without damaging the wire,
3. Self sealing structure, moisture-proof, water-proof and anti-corrosion, extending the service life of insulated conductors and clamps
4. Special contact blade is used for copper (aluminum) butt joint and copper aluminum transition
5. The electrical contact resistance is small, and it is less than 1.1 times of the resistance of equal length branch conductor, meeting the DL/T765.1-2001 standard
6. Special insulating shell, anti light and environmental aging, dielectric strength>12KV
7. Curved surface design, applicable to the connection of the same (reducing) diameter conductor, with a wide connection range (0.75mm2-400mm2)
Product advantages:
1. Simple installation: cable branch can be made without stripping the insulation skin of the cable, and the joint is completely insulated. It is not necessary to cut off the main cable, and branches can be made at any position of the cable. The installation is simple and reliable. It can be installed with electricity only by using a socket wrench.
2. Safety in use: the connector is resistant to twisting, shockproof, waterproof, flame retardant, and electrochemical corrosion aging, requiring no maintenance. It has been successfully used for more than 30 years.
3. Cost saving: the installation space is very small, saving the cable tray and civil engineering costs. For application in buildings, there is no need for terminal box, distribution box, cable return, and cable investment. The cost of cable+piercing clamp is lower than that of other power supply systems, which is only about 40% of the plug-in bus and about 60% of the prefabricated branch cable.
Product installation
1. Adjust the nut of the piercing clamp to the proper position, and insert the branch wire into the branch wire cap completely.
2. Insert the main line. If the main line has two layers of insulation, a certain length of outer insulation must be stripped at the connection position.
3. Put the main/branch line in a proper position and keep them parallel. First, tighten the nut by hand to fix the clamp.
4. Tighten the nut evenly with a socket wrench of the corresponding size until the top breaks off and the installation is complete.
Installation of the double-screw insulation piercing clamp:
1. Unscrew the clamp first and snap the main wire into the main wire groove. Do not jam the main wire and the knife ruler crookedly. Pay attention to whether the wire diameter range corresponds to this wire clip.
2. Put the branch line into the branch line slot. The precautions are the same as above.
3. Tighten with a socket wrench. Open-end wrenches are disabled.
4. Note that the two nuts should be screwed down synchronously in sequence.
5. When tightened to a certain strength, the constant torque nut is twisted off. The installation is complete.
Product details
Products real shot
A corner of the production workshop
Product packaging
Product application case
/* January 22, 2024 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1
We are China Ttd Series 1kv 77-679A 1.5-400mm² Special Waterproof and Flame-Retardant Insulation Piercing Connector for Street Lamp Distribution System manufacture and supplier,You can get more details with Email,you will get cheap price or factory price.
Get Latest Price Request a quote
Popular Bolt Type Tension Clamp Products
Zh 20-30mm Right Angle Hanging Ring (Eye chain links) Power Link Fittings of Overhead Line
Qh 11-16mm Link Fitting Ball Eyes Electric Power Fittings
Jbly 10-400mm² 43*36*45mm Special-Shaped Parallel Trench Wire Clamp Overhead Cable Wire Clamp
Ty 35-630mm² 20-70mm Electric Power Fittings Hydraulic T-Clamp Single Conductor Branch Clamp
Xgu 5-26mm Jumper Suspension Clamp Electric Power Fittings
Popular cnkcele Products
Nxl 35-240mm² 14.5-36.4kn Wedge Insulation Self-Locking Tension Clamp
Jdjj2 35kv 35000/√ 3V 0.5/6p Outdoor High Voltage Oil Immersed Voltage Transformer
Lw16-40.5 35kv 1600-2000A Outdoor Three-Phase AC Sulfur Hexafluoride Circuit Breaker Auto Recloser
XL-21 380V 800A New Low-Voltage Dustproof Distribution Box Power Cabinet
Yjv22 0.6/1kv 10-400mm² 2-5 Core Low and Medium Voltage Armored Pure Copper Cross-Linked Power Cable
Byd 35-240mm² 1-10kv Overhead Insulated Power Line Electric-Check Grounding Ring Device
Popular Overhead Insulated Conductor Fittings Products
Qh 11-16mm Link Fitting Ball Eyes Electric Power Fittings
Ny 185-800mm² Tension Clamp for Heat-Resistant Aluminum Alloy Stranded Wire
Jbly 10-400mm² 43*36*45mm Special-Shaped Parallel Trench Wire Clamp Overhead Cable Wire Clamp
Mwl 63-125mm Outdoor Supports for Bar (Vertical setting) Substation Fitting