33kv S11 Type off-Circuit Tap Changing Transformers
33kv S11 Type off-Circuit Tap Changing Transformers image
Get Latest Price Request a quote
Quick Details
Product Details
1. Low loss, therefore significantly energy-saving. The average no-load loss is 35% lower, and the load loss 10~20% lower, than
Prescribed by the present National standard GB/T 6451.
2. The core laminations are made up from imported high-quality cold-rolled grain-oriented silicon steel sheets with miter joints
And without punched holes, and are stacked without the upper yoke sheets in place. After stacking, the core is pressed
Integrally and finally glued together by epoxy resin on the cut edges, so that the three limbs and the upper and lower yokes are
Bonded together into a rigid, vertically straightened entity, together with the plate-type upper and lower frame.
3. Zigzag directed flow of oil are provided within the windings, so that all parts of the windings can be cooled more evenly, thus
Reducing the temperature rise of the windings as a whole as well as the hot-spot temperature rise, prolonging the service life
Of transformers.
4. The regulating winding is a separate winding, apart from the high voltage main winding. In this way, total ampere-turn balance
Between windings can be obtained irrespective of the tapping position; And the axial electrodynamic force during short circuit
Can be much reduced, thus upgrading the short circuit withstand capability of the transformer as a whole. All the windings are
Perfectly dried before assembly. The radial clearances between windings and between low voltage winding and core are filled
With pre-dried vertical spacers and insulating cylinders in such a way that the windings are tightly together radially with
Practically ‘zero’ allowance between them.
5. The windings of one phase are assembled into an integral phase block before placing onto the core. The low voltage winding is
Wound directly on strong thick paper cylinder. Vertical spacer strips are provided in spaces between windings and outside the
Outermost winding. The radial dimensions of all windings are kept within strict tolerance, so that a rigid winding phase block
Are obtained, capable of withstanding all the radial short-circuit forces encountered in service, and the possibility of buckling
Of the inner winding is obviated. Axially, the height of all windings is kept within close tolerance. Horizontal spacers between
Discs of a winding are pre-densified. The assembled winding phase black are pressed up and down by single support and
Pressure plates after careful adjustment of the heights of individual windings. Axial pressures are co-ordinated with the
Calculated short circuit force, so that the capability of the transformer to withstand axial short-circuit force is much increased.
6. The winding manufacture, winding assembly, and core and winding assembly work are all proceeded in totally closed clean
Rooms inside workshops. The cleanliness and temperature stability requirement of the area are the same as that required for
The manufacture of 500kV class transformers. The final vapor phase drying of the core and coil assembly is practically a further
Cleaning process.
7. Core frames in the form of a flat plate are used for clamping the core, and are joined together by side beams. The core and coil
Assembly is fixed in the tank, being positioned against the tank at six sides rigidly, such that there can be no displacement of
The assembly due to impacts during transport. Three-dimensional impact recorders are installed on transformers during
Transport to detect whether or not unacceptable impact force has been experienced and displacement of the core and coil
Assembly occurred during transportation. If not, lifting of the core and coil assembly out of the tank is not necessary. Flat cover
Permits the bushings to be mounted in a vertical posi
We are China 33kv S11 Type off-Circuit Tap Changing Transformers manufacture and supplier,You can get more details with Email,you will get cheap price or factory price.
Get Latest Price Request a quote
Popular Amorphous Transformer Products
ANSI Type Three Phase Pad Mount Dead Front Transformer
Three Phase Tap Changer 230kv Power Transformers
33kv Medium Voltage Dry Type Distribution Transformers
33kv Sz11 Type on-Load Tap Changer Transformers
Three Phase Two Winding off Circuit Tap Changing Transformers 33kv
Sc10 Type 33kv Dry Type Power Transformerwith off-Circuit Switch
Popular Oil Transformet Products
230kv 132kv Oil-Immersed Power Transformer IEC Standard
Three Phase Overhead Pole Mounted 11kv Distribution Transformer
630~2500kVA 11kv 12kv 15kv Distribution Transformers
Oil Immersed Distribution Transformer 20kv IEC Standard
11kv D11 Single-Phase Oil Immersed Transformer
230kv Three-Phasetwo-Winding off-Circuit Tap Changing Power Transformers
Popular Power Transformer Products
11kv 33kv Oil Immersed Power Transformer Distribution Transformer
230kv 132kv 126kv Oil-Immersed Power Transformer
11-33kv Sc (H) 11-30~500kVA 10kv Distribution Transformers
S11 Type 33kv off-Circuit Tap Changing Transformers
Single Phase Overhead Step up Step Down Distribution Transformer 11kv
Step Voltage Regulator Oil Immersed
Popular silverstone-electric Products
ANSI Standard Type Porcelain Ceramic Strain Insulator
Vintage Brown Butterfly Insulator / Shackle Insulator ED-2b IEC Standard
ANSI Disc Suspension Porcelain Insulators
Epoxy Resin Cast Post Insulator for Switchgear APG
High Temperature Resistant Colorful PE Heat Shrink Tube Shrinkable Sleeves Shrinking Tube
Top Station Porcelain Insulator ANSI 57-2 for Hv
Tags: Amorphous Transformer, Oil Transformet, Power Transformer, silverstone-electric