Tie Strap 900mm
Tie Strap 900mm image
Get Latest Price Request a quote
Quick Details
Product Details
The strap shall have a cross section dimension of 50 x 5 mm
The strap shall have a cross section dimension of 50 x 5 mm.
The strap manufactured for suspension/intermediate assembly according to the given drawing (see the drawing)
Yield strength of tie strap must be 240N/mm2.
To protect tie strap from corrosion it shall be hot dip-galvanized.
Guaranteed Value
The following values are guaranteed by the manufacturers as stipulated by the guaranteed characteristics table
§ Each and every dimension
§ Material strength.
3.7.4. Testing
The following testing must be carried out.
a. Visual inspection
b. Size and dimension verification.
U channel cross-arm for 33kV
Any standard equivalent to GB/T 707 1988, 80×43, 5/8 and 100×48, 5.3/8.5 is accepted.
For suspension, T-off, angle and dead end assembly shall have a cross section dimension of
80 x 43 x 5/8mm
For transformer base U-cross arms shall have a dimension of 100x48x5.3/8.5
U-cross arms manufactured for suspension, T-off, angle, dead end and transformer base
assembly as per the drawing
To protect U-cross arms against corrosion U-cross arms shall be hot dip-galvanized
Yield strength of U-cross arm 240N/mm2
Test for yield stress
Percentage elongation test
Bend test
Chemical composition test
Galvanization tests thickness of Zn coating
Weight of Zn Coating
Uniformity of Zn coating
Adhesion test of Zn coating
Visual inspection
Weight verification
Dead end hook 382
Hook threaded nominal diameter (A) 16mm
Minor threaded diameter (W) 14
Thickness of nut (M), washer diameter and thickness as per BS standard
Yield strength of pin must be 240N/mm2
LV Hook from corrosion it shall be hot dip-galvanized
Visual inspection
Size inspection
Galvanizing test
Strength test
Suspension hook M16-380
Hook threaded nominal diameter (A) 16mm
Minor threaded diameter (W) 14
Thickness of nut (M), washer diameter and thickness as per BS standard
Yield strength of pin must be 240N/mm2
To protect LV Hook from corrosion it shall be hot dip-galvanized
Testing
Visual inspection
Size inspection
Galvanizing test
Strength test
The following testing shall be carried out
Dead End Clamp ,Anchoring Clamp
The clamps should be designed to Anchor LV AB cable with insulated messenger. The clamp
should anchor/hold the neutral messenger without damaging the insulation.
The clamp should conform to the standard NFC 33041 and 33042 or equivalent. The clamp
body should be made of corrosion resistant Aluminium alloy, bail should be of stainless steel
and self adjusting wedges should be weather and UV resistant polymer.
Anchoring assemblies are used to firmly attach the messenger of ABC to a support and
transmit the mechanical tension at the end of a run or to the supporting structures at a major
change in direction.
The suspension clamp shall be manufactured from weather and UV light resistant reinforced
nylon and aluminum alloy. The clamp should provide an additional insulation between the
cable and the pole.
Clamps should be fixed with pole by eyehook/bracket. Breaking load should not be less than
15kN
Suspension Assembly is used for supporting an ABC by installation on the messenger at an
intermediate point of support such as a pole. It can accommodate small angles of deviation up
to 30o. The clamp should hold insulated messenger of diameter range from 6mm up to 12 mm.
Visual examination
Dimensional and material verification
Tensile strength
Dielectric voltage test
Climatic & corrosion ageing
Endurance test under mechanical and thermal stresses
Electrical ageing
TYPE:APG-C4
NAME:Parallel groove clamp APG-C4
Specification
Material |
||
Material standard |
||
Range of conductor cross-section |
16…50/2.5…35 |
|
Range of conductor diameter, Al/Cu |
mm2 |
|
Tensile strength |
KN | 5 |
Thickness of zinc coating, |
mm |
43 |
Test voltage at 50Hz for one minute in water |
kV |
6 |
Al 35-300mm² Size 105*65mm Tri-bolts Bolt M10*60 Weight 560g
We are China Tie Strap 900mm manufacture and supplier,You can get more details with Email,you will get cheap price or factory price.
Get Latest Price Request a quote
Popular Anchoring Clamp Products
Tension Clamp Strain Clamp Anchoring Clamp Tension Connector
Preformed Tension Clamp/Preformed Suspension Clamp Electrical Cable Fittings
M16, 300mm Long Bolt Nut and Washer
Tension Clamp Dead End Clamp Strain Clamp Suspension Clamp Anchoring Clamp
Anchoring Clamp Aluminum Alloy, Nylon Plus Fiber Glass, Stainless Steel.
Popular Crossarm Products
Hot DIP Galvanized 15holes Crossarm, Intermediate Crossarm, Angle Iron
Hot-DIP Galvanized Steel Cross Arms for Pole Line Fitting
Alley Arm Brace Hot DIP Galvanized Angle Brace for Electrical Crossarm
Stay Rod Equipment and Binding Accessories
Electrical Galvanized Mild Steel Cross Arm Angel Crossarm Channel Cross-Arm Overhead Line Hardware
Popular Dead End Hook Products
M16, 400mm Long Bolt Nut and Washer
Popular jgtrade1 Products
Best Price24kv 100A Ceramic Types Drop out Fuses Cutout/Cut out Fuse
Nut, Nu Clamp (ajustable type)
Box Type Fixed Totally Enclosed Switchgear
High-Voltage Disconnector Switch 21kv
Street Lamp Special Distribution Box
100mm2 AAC Wasp Bare Conductor
Tags: Anchoring Clamp, Crossarm, Dead End Hook, jgtrade1