Pre-Insulated Bimetal Sleave
Pre-Insulated Bimetal Sleave image
Get Latest Price Request a quote
Quick Details
Product Details
The following documents were referred to during the preparation of this specification. In case of conflict, the provisions of this specification shall take precedence.
IEC 129:1975: Alternating Current Disconnectors (Isolators) and Earthing Switches
IEC 60694:2002: Common Specifications for High Voltage Switchgear and Controlgear
BS 729: Hot dip galvanized coating on iron and steel articles
IEC62271-102
Isolator (Disconnector) – a mechanical switching device which provides, in the open position, an isolating distance in accordance with Electrical Safety requirements.
SERVICE CONDITIONS
The isolator shall be suitable for continuous operation outdoors in tropical areas at altitudes of up to 2200m above sea level, humidities of up to 90%, average ambient temperature of +30ºC with a minimum of -1ºC and a maximum of +40ºC and heavy saline conditions along the coast.
4.2. DESIGN AND CONSTRUCTION
4.2.1 The Isolator, Solid Link shall be designed and constructed in accordance with IEC 129 and IEC 60694.
4.2.2 The isolating link shall be of the vertical opening, designed for single phase manual operation. It shall be easily removed and replaced by using a portable operating rod.
4.2.3 The isolating link shall incorporate double porcelain insulators to suit voltage requirements and mounted on hot dipped galvanised steel under base suitable for vertical mounting.
4.2.4 The isolating link shall be arranged so that each unit is mounted independently on an angle bracket. It shall be supplied complete with the angle bracket and accessories suitable for mounting on ‘U’ type steel channel. The drawings to be submitted shall indicate all the applicable mounting positions.
4.2.5 The isolator shall be designed such that in fully open position, it shall provide adequate electrical isolation between the contacts on each phase. It shall conform to the requirement as single point isolation for safety.
4.2.6 All steel parts shall be hot dip galvanized to BS 729. The minimum coating of galvanizing required is 80 microns.
4.2.7 The solid link shall be removable from the mounting by use of operating rod.
4.2.8 All current carrying parts of the isolator shall be made of high conductivity material.
4.2.9 The isolator shall be fitted with clamp connectors for Aluminium (ACSR) conductor of Aluminium (ACSR)conductor of up to 18.2mm diameter.
The rating of the complete isolator shall be as follows: –
Rated voltage
36 kV
Rated frequency
50 Hz
Rated lightning impulse withstand voltage
200 kV
Rated power frequency withstand voltage, dry
95 kV
Rated normal current
400 Amps
Rated short time withstand current for 3 sec, min.
18.0 kA
Minimum creepage distance of insulators
900 mm
Recommended for You
Not exactly what you want?
Post Sourcing Request
Hot Searches
Switch Box
Time Switch
Air Switch
Voltage Switch
Level Switch
We are China Pre-Insulated Bimetal Sleave manufacture and supplier,You can get more details with Email,you will get cheap price or factory price.
Get Latest Price Request a quote
Popular Disconnector Switch Products
Gw9-12kv Outdoor Disconnect Switch Isolating Break Switch
High and Low Voltage Electroscope
High -Voltage Isolate Switch 12kv 600A
Iacm Switch Disconnector 100A - 36kv with Socket and Command
Gw4 Outdoor High Voltage 33kv 35kv 400A 630A 1000A 1250A Three Phase Isolator
Disconnect Switch 145 Kv, 40 Ka, 3150 a with Grounding Blades
Popular jgtrade1 Products
High -Voltage Isolate Switch 40.5kv
Fjz Square Frame Spacers Dampers
Jla-3 Special Grounding Wire for Power Plant
Fuse Cutout, Drop out Fuses 24kv 200A 10ka
High Voltage Henging Cable Cleat
Popular Rotary Switch Products
Factory Price High Voltage AC 12kv Outdoor Disconnect Switch
34.5/0.433kv, 315kVA Pole Mounted Distribution Transformer
Substation Disconnector Double Break Switch
Popular Switch Disconnector Products
34.5/0.433kv, 500kVA Ground Mounted Distribution Transformer
75kv Isolator Switch Images Vertical Break Disconnector and Isolator
Preformed Guy Grip 7/8 Swg Dead Ends
Tags: Disconnector Switch, jgtrade1, Rotary Switch, Switch Disconnector